WLAN Access Point (Enclave-NIPRNet Connected) Security Technical Implementation Guide (STIG)
Pick two releases to diff their requirements.
Open a previous version of this STIG.
- RMF Control
- Severity
- M
- CCI
- Version
- NET1639
- Vuln IDs
-
- V-3014
- Rule IDs
-
- SV-3014r2_rule
Checks: C-3540r4_chk
Review the management connection for administrative access and verify the network element is configured to time-out the connection after 10 minutes or less of inactivity.
Fix: F-3039r4_fix
Configure the network element to ensure the timeout for unattended administrative access connections is no longer than 10 minutes.
- RMF Control
- Severity
- H
- CCI
- Version
- NET0460
- Vuln IDs
-
- V-3056
- Rule IDs
-
- SV-3056r5_rule
Checks: C-3503r9_chk
Review the network device configuration and validate there are no group accounts configured for access.
Fix: F-3081r9_fix
Configure individual user accounts for each authorized person then remove any group accounts.
- RMF Control
- Severity
- M
- CCI
- Version
- NET0465
- Vuln IDs
-
- V-3057
- Rule IDs
-
- SV-3057r3_rule
Checks: C-3504r6_chk
Review the accounts authorized for access to the network device. Determine if the accounts are assigned the lowest privilege level necessary to perform assigned duties. User accounts must be set to a specific privilege level which can be mapped to specific commands or a group of commands. Authorized accounts should have the greatest privilege level unless deemed necessary for assigned duties. If it is determined that authorized accounts are assigned to greater privileges than necessary, this is a finding.
Fix: F-3082r5_fix
Configure authorized accounts with the least privilege rule. Each user will have access to only the privileges they require to perform their assigned duties.
- RMF Control
- Severity
- M
- CCI
- Version
- NET1638
- Vuln IDs
-
- V-3069
- Rule IDs
-
- SV-3069r3_rule
Checks: C-3532r7_chk
Review the network device configuration to verify only secure protocols using FIPS 140-2 validated cryptographic modules are used for any administrative access. Some of the secure protocols used for administrative and management access are listed below. This list is not all inclusive and represents a sample selection of secure protocols. -SSHv2 -SCP -HTTPS -SSL -TLS If management connections are established using protocols without FIPS 140-2 validated cryptographic modules, this is a finding.
Fix: F-3094r5_fix
Configure the network device to use secure protocols with FIPS 140-2 validated cryptographic modules.
- RMF Control
- Severity
- L
- CCI
- Version
- NET1640
- Vuln IDs
-
- V-3070
- Rule IDs
-
- SV-3070r2_rule
Checks: C-3542r4_chk
Review the configuration to verify all attempts to access the device via management connection are logged.
Fix: F-3095r3_fix
Configure the device to log all access attempts to the device to establish a management connection for administrative access.
- RMF Control
- Severity
- H
- CCI
- Version
- NET0240
- Vuln IDs
-
- V-3143
- Rule IDs
-
- SV-3143r2_rule
Checks: C-40236r1_chk
Review the network element configuration to determine if the vendor default password is active.
Fix: F-35391r2_fix
Remove any vendor default passwords from the network element configuration.
- RMF Control
- Severity
- H
- CCI
- Version
- NET1636
- Vuln IDs
-
- V-3175
- Rule IDs
-
- SV-3175r3_rule
Checks: C-3516r7_chk
Review the network device configuration to verify all management connections for administrative access require authentication.
Fix: F-3200r3_fix
Configure authentication for all management connections.
- RMF Control
- Severity
- H
- CCI
- Version
- NET1665
- Vuln IDs
-
- V-3210
- Rule IDs
-
- SV-3210r2_rule
Checks: C-3822r5_chk
Review the network element configuration and verify if either of the SNMP community strings “public” or “private” is being used.
Fix: F-3235r4_fix
Configure unique SNMP community strings replacing the default community strings.
- RMF Control
- Severity
- M
- CCI
- Version
- WIR0125-01
- Vuln IDs
-
- V-3515
- Rule IDs
-
- SV-3515r2_rule
Checks: C-22364r1_chk
Detailed Policy requirements: Encryption requirements for data in transit: - The WLAN infrastructure (e.g., access point, bridge, or WLAN controller) and WLAN client device must be configured to use the AES-CCMP encryption protocol. Check procedures: - Interview IAO and review WLAN system documentation. - Determine if the WLAN network and client components encryption setting has been configured to use the AES-CCMP encryption protocol and no others. - Mark as a finding if the WLAN is configured to support any encryption protocol other than AES-CCMP, even if AES-CCMP is one of several supported options.
Fix: F-3446r1_fix
Implement AES-CCMP to protect data in transit. Deactivate encryption protocols other than AES-CCMP.
- RMF Control
- Severity
- M
- CCI
- Version
- WIR0115-01
- Vuln IDs
-
- V-3692
- Rule IDs
-
- SV-3692r2_rule
Checks: C-16042r3_chk
NOTE: If the equipment is WPA2 certified, then it is capable of supporting this requirement. Review the WLAN equipment configuration to check EAP-TLS is actively used and no other methods are enabled. Mark as a finding if either EAP-TLS is not used or if the WLAN system allows users to connect with other methods. Note: DoDI 8420.01 provides the capability for the DAA to grant limited exceptions to this requirement.
Fix: F-34114r1_fix
Change the WLAN configuration so it supports EAP-TLS, implementing supporting PKI and AAA infrastructure as necessary. If the WLAN equipment is not capable of supporting EAP-TLS, procure new equipment capable of such support.
- RMF Control
- Severity
- M
- CCI
- Version
- NET1624
- Vuln IDs
-
- V-3967
- Rule IDs
-
- SV-3967r2_rule
Checks: C-3511r3_chk
Review the configuration and verify a session using the console port will time out after 10 minutes or less of inactivity.
Fix: F-3900r4_fix
Configure the timeout for idle console connection to 10 minutes or less.
- RMF Control
- Severity
- H
- CCI
- Version
- NET1623
- Vuln IDs
-
- V-4582
- Rule IDs
-
- SV-4582r3_rule
Checks: C-3510r4_chk
Review the network device's configuration and verify authentication is required for console access.
Fix: F-4515r4_fix
Configure authentication for console access on the network device.
- RMF Control
- Severity
- M
- CCI
- Version
- NET1637
- Vuln IDs
-
- V-5611
- Rule IDs
-
- SV-5611r2_rule
Checks: C-3527r4_chk
Review the configuration and verify management access to the device is allowed only from hosts within the management network.
Fix: F-5522r3_fix
Configure an ACL or filter to restrict management access to the device from only the management network.
- RMF Control
- Severity
- M
- CCI
- Version
- NET1645
- Vuln IDs
-
- V-5612
- Rule IDs
-
- SV-5612r2_rule
Checks: C-3534r4_chk
Review the configuration and verify the timeout is set for 60 seconds or less. The SSH service terminates the connection if protocol negotiation (that includes user authentication) is not complete within this timeout period.
Fix: F-5523r4_fix
Configure the network element so it will require a secure shell timeout of 60 seconds or less.
- RMF Control
- Severity
- M
- CCI
- Version
- NET1646
- Vuln IDs
-
- V-5613
- Rule IDs
-
- SV-5613r2_rule
Checks: C-3538r4_chk
Review the configuration and verify the number of unsuccessful SSH login attempts is set at 3.
Fix: F-5524r7_fix
Configure the network element to require a maximum number of unsuccessful SSH login attempts at 3.
- RMF Control
- Severity
- L
- CCI
- Version
- NET1629
- Vuln IDs
-
- V-7011
- Rule IDs
-
- SV-7365r2_rule
Checks: C-3513r3_chk
Review the configuration and verify the auxiliary port is disabled unless a secured modem providing encryption and authentication is connected.
Fix: F-6614r3_fix
Disable the auxiliary port. If used for out-of-band administrative access, the port must be connected to a secured modem providing encryption and authentication.
- RMF Control
- Severity
- M
- CCI
- Version
- NET0813
- Vuln IDs
-
- V-14671
- Rule IDs
-
- SV-15327r2_rule
Checks: C-12793r5_chk
Review the device configuration and verify it is authenticating the NTP messages received from the NTP server or peer. Authentication must be performed using either PKI (supported in NTP v4) or SHA-1 hashing algorithm. If SHA-1 is not supported by both the NTP client and server, then MD5 can be used.
Fix: F-14132r1_fix
Configure the device to authenticate all received NTP messages using either PKI (supported in NTP v4) or SHA-1 hashing algorithm. If SHA-1 is not supported by this client or the NTP peer or server, then MD5 can be used.
- RMF Control
- Severity
- M
- CCI
- Version
- NET1647
- Vuln IDs
-
- V-14717
- Rule IDs
-
- SV-15459r2_rule
Checks: C-12924r6_chk
Review the configuration and verify SSH Version 1 is not being used for administrative access.
Fix: F-14184r3_fix
Configure the network element to use SSH version 2.
- RMF Control
- Severity
- L
- CCI
- Version
- WIR0105
- Vuln IDs
-
- V-14846
- Rule IDs
-
- SV-15614r1_rule
Checks: C-13276r1_chk
Review device configuration. 1. Obtain the SSID using a wireless scanner or the AP or WLAN controller management software. 2. Verify the name is not meaningful (e.g., site name, product name, room number, etc.) or set to the manufacturer's default value. Mark as a finding if the SSID does not meet the requirement listed above.
Fix: F-34142r1_fix
Change the SSID to a pseudo random word that does not identify the unit, base, or organization.
- RMF Control
- Severity
- M
- CCI
- Version
- WIR0135
- Vuln IDs
-
- V-14886
- Rule IDs
-
- SV-15654r1_rule
Checks: C-13412r1_chk
Detailed policy requirements: Wireless access points and bridges must not be directly connected to the enclave network. A network device must separate wireless access from other elements of the enclave network. Sites must also comply with the Network Infrastructure STIG configuration requirements for DMZ, VLAN, and VPN configurations, as applicable. Examples of acceptable architectures include placing access points or controllers in a screened subnet (e.g. DMZ separating intranet and wireless network) or dedicated virtual LAN (VLAN). Additional discussion of WLAN architectures is found in the Wireless Overview document contained in the Wireless STIG package. NOTE: See Figure 3-1 in the Wireless STIG for an example of an acceptable network architecture. Check Procedures: Review network architecture with the network administrator. 1. Verify compliance by inspecting the site network topology diagrams. 2. Since many network diagrams are not kept up-to-date, walk through the connections with the network administrator using network management tools or diagnostic commands to verify the diagrams are current. Mark as a finding if site wireless infrastructure such as access points and bridges are not isolated from the enclave network.
Fix: F-3448r1_fix
Remove wireless network devices with direct connections to an enclave network. If feasible, reconfigure network connections to isolate the WLAN infrastructure from the enclave network, separating them with a firewall or equivalent protection.
- RMF Control
- Severity
- M
- CCI
- Version
- WIR0110
- Vuln IDs
-
- V-14888
- Rule IDs
-
- SV-15656r1_rule
Checks: C-13416r1_chk
1. Review the relevant configuration screen of the WLAN controller or access point. 2. Verify the session timeout setting is set for 30 minutes or less. 4. Mark as a finding if any of the following are found. - Session timeout is not set to 30 minutes or less for the entire WLAN. - The WLAN does not have the capability to enable the session time-out feature.
Fix: F-34136r1_fix
Set the WLAN inactive session timeout to 30 minutes or less.
- RMF Control
- Severity
- L
- CCI
- Version
- WIR0120
- Vuln IDs
-
- V-14889
- Rule IDs
-
- SV-15657r1_rule
Checks: C-13418r1_chk
Review documentation and inspect AP locations. 1. Review documentation showing signal strength analysis from site survey activities, if available. 2. Use testing equipment or WLAN clients to determine if the signal strength is, in the reviewer’s judgment, excessively outside the required area (e.g., strong signal in the parking area, public areas, or uncontrolled spaces). 3. Lower end APs will not have this setting available—in this case, the site should locate the APs away from exterior walls to achieve compliance with this requirement. 4. Mark as a finding if any of the following is found. o Visual inspection of equipment shows obvious improper placement of APs where it will emanate into uncontrolled spaces (e.g., next to external walls, windows, or doors; uncontrolled areas; or public areas). o Building walk-through testing shows signals of sufficient quality and strength to allow wireless access to exist in areas not authorized for WLAN access.
Fix: F-3445r1_fix
Move APs to areas in which signals do not emanate in a manner making them usable outside the areas authorized for WLAN access. Alternatively, replace omni-directional antennae with directional antennae if this will solve the problem. If these solutions are not effective, then adjust the transmission power settings on the AP to reduce the usability of signals in unauthorized areas. If the WLAN equipment does not allow the transmission power to be adjusted, and the APs are placed in a location where the IAO determines there is significant risk that an adversary could be present in location where signals may be intercepted, then the site should procure WLAN equipment that permits power adjustment.
- RMF Control
- Severity
- M
- CCI
- Version
- NET0991
- Vuln IDs
-
- V-17821
- Rule IDs
-
- SV-19075r2_rule
Checks: C-19238r3_chk
The managed network element’s OOBM interface must be configured with an IP address from the address space belonging to the OOBM network. After determining which interface is connected to the OOBM access switch, review the managed device configuration and verify the interface has been assigned an address from the local management address block.
Fix: F-17736r1_fix
Configure the managed network element’s OOBM interface with an IP address from the address space belonging to the OOBM network.
- RMF Control
- Severity
- M
- CCI
- Version
- NET0992
- Vuln IDs
-
- V-17822
- Rule IDs
-
- SV-19076r2_rule
Checks: C-19239r4_chk
Step 1: Verify the managed interface has an inbound and outbound ACL or filter. Step 2: Verify the ingress ACL blocks all transit traffic—that is, any traffic not destined to the router itself. In addition, traffic accessing the managed elements should be originated at the NOC. Step 3: Verify the egress ACL blocks any traffic not originated by the managed element.
Fix: F-17737r1_fix
If the management interface is a routed interface, it must be configured with both an ingress and egress ACL. The ingress ACL should block any transit traffic, while the egress ACL should block any traffic that was not originated by the managed network elements.
- RMF Control
- Severity
- L
- CCI
- Version
- NET0812
- Vuln IDs
-
- V-23747
- Rule IDs
-
- SV-28651r2_rule
Checks: C-3581r3_chk
Review the configuration and verify two NTP servers have been defined.
Fix: F-3044r1_fix
Specify two NTP server IP addresses on the device to be used to request time from.
- RMF Control
- Severity
- M
- CCI
- Version
- NET0405
- Vuln IDs
-
- V-28784
- Rule IDs
-
- SV-36774r2_rule
Checks: C-35853r2_chk
Verify the call home service or feature is disabled on the device.
Fix: F-31103r1_fix
Configure the network device to disable the call home service or feature.
- RMF Control
- Severity
- M
- CCI
- Version
- WIR0116
- Vuln IDs
-
- V-30257
- Rule IDs
-
- SV-39895r2_rule
Checks: C-38915r3_chk
Detailed Policy Requirements: Certificate-based PKI authentication must be used to connect WLAN client devices to DoD networks. The certificate-based PKI authentication should directly support the WLAN EAP-TLS implementation. At least one layer of user authentication must enforce network authentication requirements found in JTF-GNO CTO 07-15Rev1 (e.g., CAC authentication) before the user is able to access DoD information resources. Check Procedures: Interview the site IAO and SA. Determine if the site’s network is configured to require certificate-based PKI authentication before a WLAN user is connected to the network. Mark as a finding if certificate-based PKI authentication is not required prior to a DoD WLAN user accessing the DoD network.
Fix: F-34052r2_fix
Integrate certificate-based PKI authentication into the WLAN authentication process.